POLICIES

FOCUS AND SCOPE

Journal of Chemical Process Engineering is a journal that publishes scientific articles from various experimental, analytical, and case studies, natural resources and energy technology.

Journal of Chemical Process Engineering has p-ISSN: 2527-4457 and  e-ISSN: 2655-2957. Journal of Chemical Process Engineering is published by Department of Chemical Engineering, Faculty of Industrial Technology, Universitas Muslim Indonesia, Makassar which is published every year in May and October

Journal of Chemical Process Engineering are articles have review by our Bestari Partners (peer-reviewers). The decision to accept or not a scientific article in this journal depend of Editorial Board based on recommendations from Bestari Partners.

The Focus and Scope of the Journal are :
  • Chemical and Process Technology
  • Energy, Water, Environment and Sustainability
  • Coal , oil and Gas Technology
  • Bioreseurce and Biomass Technology
  • Particle Technology
  • Separation  and Purification Technology
  • Food Technology
  • Catalyst  & Kinetics Technology
  • Essensial Oil Technology
  • Sugar Technology
  • Material and Biomaterial Technology
  • Biomedical Engineering
  • Mineral Processing
  • Powder Technology

Since in 2016,  Journal of Chemical Process Engineering only accepts articles from research and case study. Journal of Chemical Process Engineering Journal is sent electronically by OJS system https://jurnal.fti.umi.ac.id/index.php/JCPE

OPEN ACCESS POLICY

Jurnal of Chemical Procecss Engineering provides immediate open access to its content on the principle that making research freely available to the public to supports a greater global exchange of knowledge.

All articles published Open Access will be immediately and permanently free for everyone to read and download. Journal of Chemical Procecss Engineering is licensed under: 

Lisensi Creative Commons
Journal of Chemical Process Engineering is licences under :  Lisensi Creative Commons Atribusi-NonKomersial-BerbagiSerupa 4.0 Internasional.

PEER-REVIEWED POLICY

All manuscripts and articles submitted to Journal of Chemical Process Engineering are subject to peer review process and are expected to meet standards of academic excellence. If approved by the editor, submissions will be considered by double-blind peer-reviewers, whose all personal identities will remain anonymous to the authors. If your article is based on a conference/seminar article which may have been published elsewhere, it is important that you observe the following: The submitted article must have been substantially revised, expanded and rewritten so that it is significantly/totally different from the conference/seminar paper or presentation on which it is based. The article must be sufficiently or totally different to make it a new, original work. As a guide, you should aim to have more than 80% new material/content. This is a matter of judgment and will be based on a comparison of the submitted article with the original conference/seminar paper. The original conference/seminar article should be supplied by the author of the expanded article for the purpose of comparison. All such articles will be subject to the same review process as any other submitted article. If the original conference article on which the extended article is based has been published elsewhere, or the copyright has been assigned to the conference organizers or another party, authors should ensure that they have cleared any necessary permissions with the copyright owners. Articles will not be accepted, post-review, for publication unless such written permissions have been provided along with the author.

The review process will take about one to three months. Articles accepted with minor or major revisions should be revised as the reviewers comments and suggestions.

PLAGIARISM

Papers submitted to Journal of Chemical Process Engineering will be screened for plagiarism using CrossCheck/iThenticate/Turnitin plagiarism detection tools. Journal of Chemical Process Engineering will immediately reject papers leading to plagiarism or self-plagiarism. Before submitting articles to reviewers, those are first checked for similarity/plagiarism tool, by a member of the editorial team. The papers submitted to Journal of Chemical Process Engineering must have a similarity level of less than 20%.

Plagiarism is the exposure of another person’s thoughts or words as though they were your own, without permission, credit, or acknowledgment, or because of failing to cite the sources properly. Plagiarism can take diverse forms, from literal copying to paraphrasing the work of another. In order to properly judge whether an author has plagiarized, we emphasize the following possible situations:

An author can literally copy another author’s work- by copying word by word, in whole or in part, without permission, acknowledge or citing the original source. This practice can be identified by comparing the original source and the manuscript/work who is suspected of plagiarism.

Substantial copying implies an author to reproduce a substantial part of another author, without permission, acknowledge or citation. The substantial term can be understood both in terms of quality as quantity, being often used in the context of Intellectual property. Quality refers to the relative value of the copied text in proportion to the work as a whole.

Paraphrasing involves taking ideas, words or phrases from a source and crafting them into new sentences within the writing. This practice becomes unethical when the author does not properly cite or does not acknowledge the original work/author. This form of plagiarism is the more difficult form to be identified.